Search results for: 'comes for harden door locks for classic'
-
Dor-o-Matic 1690/1990 Top Rod Latch Assembly PB130
The Dor-o-Matic 1690/1990 Top Rod Latch Assembly PB130 is also used on the 1390, 1490 and 2390. This latch has been around since the 1970's, and is usually the issue if your bottom rod is dragging on the floor. Although we are calling it Dor-o-Matic, it is actually known as a Falcon SU Top Latch due to a name change 5 or 6 years ago. This latch rolls over when the device is pressed in and then locks in that position. When the door closes, the 'U" channel of the latch flips over to a vertical postion and drops the rods. This latch always uses the PB48 Strike, our part # G199034. The Dor-o-Matic Panic Devices have been around since the late 1960’s, but have most recently been known as the Falcon Panic Device from a name change they had in about 2008. They are basically the same device, with the same parts, just a different name plate. Falcon part # PB130 or 4270101806.
G199025 -
Von Duprin 2670 Guard-X Panic Device
Heavy Duty Design
The new Series 2670 Exit Alarm Lock provides secure protection through a large stainless steel deadbolt, which is 2" x 1/2" (51mm x 13mm) and has over a 3/4" (19mm) throw. The engagement area into the strike is over 1 1/4" (32mm) square inches. The cast aluminum latch case protects the internal mechanism and resists tampering or vandalism from inside the door. This unit has been tested to withstand up to 1600 pounds of static load force against the door.Fits 36" to 48" doors.
Uses 9 volt battery
Ships with all mounting hardware and strike.2670EO- -
Polished Stainless Steel Kick Plate | US32 Kick Plate | Polished Chrome
The Polished Stainless Steel Door Kick Plate is 16 gauge, or .050″ thick. Stainless steel offers one of the best material for commercial applications. They are very hard, and do not dent easily. The also offer the best corrosion resistances out there. We often have people looking for Brushed Chrome or Polished Chrome, but the appearance of the two finishes next to each other is very difficult to tell which is which. Also a brushed chrome or polished chrome kick plate would be a brass plate which is then chrome plated and brushed or polished depending on the plate. Brass is a soft metal that dents easily, and also does not offer the corrosion resistance that stainless steel does. Since stainless steel is stable in any environment, they do not have to clear coat the plate.
Kick Plates can be mounted by screws, two way tape, and they can be glued to the door. Our plates come standard with screw mounting. The manufacture sends #6 x 5/8″ Oval Phillips Undercut Stainless Steel screws. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10″ will have 10 holes for plates up to 33″ and 12 holes for plates between 33 and 40″.
You can order these plates with tape mounting, but on larger plates and especially plates with a stainless steel base metal, it is not recommended. Stainless Steel plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes. This is fine on the Brass and Aluminum base metals, but again Stainless Steel is very hard and a drill press would be recommended. You can glue them on, I would recommend liquid nails, and come C Clamps with the door on saw horses.Custom sizes available starting around $0.37 per square inch depending quantity.
Please allow 1 week shipping time
GKP-pol-ss -
Detex ECL-230D-PH Alarmed Panic Device
The Detex ECL-230D-PH Alarmed Exit Device is a battery operated, rugged deadbolt panic device, and is UL-Listed Panic Hardware for 36" to 48" doors. The steel paddle is photo-luminescent sign providing managed security and a 100 decibel alarm for secondary exits. The device features a single point 1" dead bolt, attack resistant design withstands over 2200 pounds of outside pull force, and is non handed. Locking and unlocking the dead bolt always arms and disarms the alarm. Rim Cylinder is not included.
ECL230DPH- -
Corbin Russwin Adjusting Nut 483F35-8
Corbin Russwin Adjusting Nut 483F35-8
This Corbin Russwin Adjusting Nut is used on the Corbin Russwin Mortise Lever Locks. It threads into the end of the spindle. 2-3/8" overall length, 9/16" thread length, 1-15/16" bolt length. The threads are 1/4-28.
Corbin Russwin part # 483F35-8
G483F35 -
Detex ECL-230D Alarmed Panic Device
The Detex ECL-230D Alarmed Exit Device is a battery operated, rugged deadbolt panic device. The steel paddle is photo-luminescent sign providing managed security and a 100 decibel alarm for secondary exits. The device features a single point 1" dead bolt, attack resistant design withstands over 2200 pounds of outside pull force and is non handed. Locking and unlocking the dead bolt always arms and disarms the alarm. Rim Cylinder is not included.
If you have a door that requires Panic Hardware, then use the ECL-230D-PH
ECL230D- -
Stainless Steel Engraved Push Plate
The Stainless Steel Engraved Push Plate is newer to our product line, but has been a very good seller. This plate is constructed of 16 gauge (.050") thick stainless steel, and comes in two different sizes, the 3-1/2" x 15", and the 4" x 16". The black engraved "PUSH" is 3/4" tall. We can only get this is stainless steel at this time, and the mounting screws are included.
GPUSH00X -
Duranodic Aluminum (Dark Brown) Door Kick Plate
The Duranodic Aluminum (Dark Brown) Door Kick Plates are dark bronze or brown and match the Dark Brown color we find on Storefront doors. These plates have an aluminum base metal, which is 18 gauge (.040") thick that is then Anodized in the Dark Brown Color. These plates relatively inexpensive. Custom sizes are available, they run about $0.25 per square inch.
You can order these plates with tape mounting, but on larger plates and especially plates with a stainless steel base metal, it is not recommended. Stainless Steel plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes. This is fine on the Brass and Aluminum base metals, but again Stainless Steel is very hard and a drill press would be recommended. You can glue them on, I would recommend liquid nails, and come C Clamps with the door on saw horses.
GKP-xxxDB -
Ives 7222INT Intermediate Pivot
• Use with 7212, 7212V or 7222 3/4 Offset Pivot
• Handed
• Vertical adjustment 3/16", include positive locking.7222INT -
Detex Narrow Stile DN Lever Trim
The Detex DN Trim is built like their exit devices, extreme durable. Designed with a break-away lever to prevent permanent damage from vandalism or abuse. Escutcheon plate measures 1-7/8 by 8-1/4 inches, the plate is 7/8 inch thick. We ship the classroom function, key locks and unlocks the lever. The levers are field reversible.
G08DNS- -
Falcon 2390 231CA Cylinder Kit
The Dor-O-Matic 2390 231CA Cylinder Kit converts your 2390 exit only to a Night Latch or Hold Back function key lock. All the hardware is included in the package to convert your device, except for the Mortise Cylinder. Housing measures 4-1/2" tall by 1-11/16" wide with a 1-1/8" projection. We send the 231CA which includes the Schlage B502-191 Cam. The 239CA is the same kit, but without the Schlage Cam.
Discontinued item, we only have a few left in Dark Bronze.
231CA- -
Dor-O-Matic 1690/1790/2390 Dogging Hex Shaft
The Dor-O-Matic 1690/1790/2390 Dogging Hex Shaft is the piece that your dog key (allen wrench) fits into the lock the device in the open or dogged position. This shaft is used on the 1690, 1790, and 2390 device. The Dor-o-Matic Panic Devices have been around since the late 1960’s, but have most recently been known as the Falcon Panic Device from a name change they had in about 2008. They are basically the same device, with the same parts, just a different name plate. The part that the hex key fits into is only about 1/4" deep, because of that these tend to get rounded out, so the key will not move the shaft.
To remove the old shaft just pull with a pair of Channel Locks or Pliers. To reinstall, just press it back in to position, you might have to bend the holding tabs back down, but we very rarely have to do this. The manufacture part number on this is SHAFT.101.
GPBX16-SHF -
Detex D Lever Trim for 10 Series
The Detex D Lever Trim is used on the 10, 20, 21 and 27 Series exit devices. The D Lever is designed to be as heavy duty as their exit devices. It features a break-away lever to prevent damage. The escutcheon measures 2-3/4 x 9-1/16 inches, with a plate thickness of 7/8 inch. We ship the classroom function, which locks and unlocks the lever.
G08DS- -
Jackson 1275 Panic Device SVR
This CRL Jackson® Exit Deviceblends the reliability of the time-proven 10 Series Crossbar Device with the sleek, contemporary style of today's modern push-pad exit device. Available in a Rim, Concealed, and Surface Vertical Rod versions, this device is suitable for use with 1-3/4" (44.5 mm) narrow, medium, and wide stile aluminum, wood, or hollow metal doors. The base is easily trimmed for field sizing, and the vertical rods are shipped to fit up to 84" (2.13 m) tall doors. Extensions or longer rods for taller doors are available. This Exit Device features an easy-to-use dogging system, and is also available with keyed cylinder dogging.
The 1200 Series touch pad with "Soft-Touch" insert requires slight pressure anywhere on the bar insert for instant release of the locking mechanism. Overall projection is only 2-7/8" (73 mm) from the door surface, and mounting hardware is concealed. Active outside trim and other panic accessories are available.
1275EO- -
International Door Closer 852P Series
The International Door Closer 852P Series is common closer we see on a lot of storefront aluminum framed doors. This is one of the last closers out there to still have sizing. By sizing I mean each door closer has a spring size of different tension so the closer is selected depending on door size and wether it is interior or exterior. These days we usually use this door closer as a replacement of existing doors. The closer features two adjustment valves for closing and latching speeds. The cylinder is constructed of precision cast aluminum. If you have an exterior door I would recommend the 880 Series, which is the same door closer, but has a back check valve. The back check valves will slow the door down if it is caught by a gust of wind. It ships with a regular arm and parallel arm bracket. This door closer is for use on doors up to 32” interior or 28” exterior doors.
3/4" x 7-3/8" mounting holes
852- -
International Door Closer 851P Series
The International Door Closer 851P Series is not a common closer we see on a lot of storefront aluminum framed doors. This is one of the last closers out there to still have sizing. By sizing I mean each door closer has a spring size of different tension so the closer is selected depending on door size and wether it is interior or exterior. These days we usually use this door closer as a replacement of existing doors. The closer features two adjustment valves for closing and latching speeds. The cylinder is constructed of precision cast aluminum. If you have an exterior door I would recommend the 880 Series, which is the same door closer, but has a back check valve. The back check valves will slow the door down if it is caught by a gust of wind. It ships with a regular arm and parallel arm bracket. This door closer is for use on doors up to 32” interior or 28” exterior doors. The 851 meets the size 1 ADA requirements.
3/4" x 6-3/8" mounting holes
851- -
Global Door Controls TC201 Door Closer
The Global Door Closer TC200 is recommended for use on all aluminum store front doors, wood or hollow metal commercial applications. It is a versatile utility closer that provides narrow styling and has a full selection of accessories to accomodate the requirement of any field installation.
In this series, our Global Door Closer TC201 is a multi-size spring model that offers adjustable power with a choice of range sizes 2-5 where high rates of closing force are required. Our TC201ADA model also offers adjustable spring power sizes 1-4 for use on interior doors requireing less than 5 lbs. of opening force and exterior doors requiring less than 8.5 lbs. This complies with ADA handicap codes and ANSI/BHMA standard requirements. Both models will retrofit most full size closers with a 9 1/16" industry standard hole patten to update any opening for code compliance.
Hole Spacing is 3/4" x 9-1/16"
Options: Specify when ordering:
- Finish - AL, DU
- Size 1-4 or 3-6
TC201-- -
Norton Door Closer 8301
The Norton Door Closer 8301 is sometimes called the Omni Door Closer. This door closer features a cast aluminum body, is a Grade 1 closer and has adjustable closing, latching, and back check speeds. This closer is a non sized closer, meaning you adjust the spring tension to meet closing requirement for a ADA Barrier Free application all the way up to a 48” exterior door. You cover might have 8301/8301BF 3301/3301BF, but the new version will cover the BF and non BF closers. The difference between this closer and the 8501 is the size of the plastic cover. The 8301 has a slim cover, and the 8501 has full cover. The hole spacing on this door closer is 3/4” x 12”.
8301- -
Von Duprin 6111 24VDC Electric Strike
Von Duprin 6111 24VDC Electric Strike
Von Duprin 6100 Series electric strikes are designed for use with Rim devices. The model 6111 retrofits model number VD 3031, and measures 1-5/8” wide, 6” high and has a backbox depth of 1-3/4”. Other voltages and replacement parts are available.
FSE - Fail-secure. Requires power to be applied to unlock the strike lip. On loss of power, the strike lip is locked-Fire Rated
FS - Fail-safe. Requires power to be applied to lock the strike lip. On loss of power, the strike lip is unlocked. Non Fire-Rated.
VD6111 -
LCN Door Closer 4021
The LCN Door Closer 4021 is also known as the Smoothee. The 4021 ships with regular arm, standard plastic cover, and self reaming and tapping screws. The 4021 is considered an application specific closer. Meaning you have to specify left and right swing door, and can only be mounted top jamb. A top jamb mount is when the closer is mounted on the top rail of the door frame and the arms hangs down and attaches to the door. Top Jamb door closers are also mounted on the pull side of the door. The Non sized cylinder will work on just about any size interior or exterior door and meets ADA requirements. We ship the 4021 REG.
4020- -
LCN Door Closer 4111 HEDA Hold Open
The LCN Door Closer 4111 HEDA Hold Open is known as the Smoothee, and is one of the heaviest duty door closers made, the HEDA stands for Hold Open Extra Duty Arm. If you have a building were you have a high traffic and abusive, especially exterior doors, then this is the closer. The 4111 is an application specific closer, meaning it will only work when mounted on the door, on the push side. This is known as a parallel arm application. The cylinder is fully adjustable and will work on doors up to 56" exterior door, and can be adjust down to ADA required levels. We ship the 4111 HEDA model, which is a hold open arm on this page. The cylinder mounting holes are 2-1/2" by 6".
4110H- -
LCN Door Closer 4111
The LCN Door Closer 4111 is known as the Smoothee, and is one of the heaviest duty door closers made. If you have a building were you have a high traffic and abusive, especially exterior doors, then this is the closer. The 4111 is an application specific closer, meaning it will only work when mounted on the door, on the push side. This is known as a parallel arm application. The cylinder is fully adjustable and will work on doors up to 56" exterior door, and can be adjust down to ADA required levels. We ship the 4111 EDA model, which is a non hold open arm, on this page. The cylinder mounting holes are 2-1/2" by 6".
4110 -
LCN Concealed Door Closer 3031
The LCN Concealed Door Closer 3031 is mortised into the top of the door. Standard 3030 series closer shipped with regular arm and wood and machine screw pack. Sized cylinders for interior doors to 4’0”. Handed for right or left swinging doors. Closers to meet ADA requirements.
3030- -
Corner Guard 311 2" X 2"
The Corner Guard 311 are a great way to protect corners in areas of high traffic and high abuse, such as warehouses and hospitals. Fabricated from 16 gauge (.050") thick metal they measure 2" on both arms, and can come in any length. Standard lengths are 36", 42" and 48", but we have the capability to modify to your specifications. They come standard with screw mounting, but other options are available.
Screws included for mounting
GCG311 -
LCN Door Closer Regular Arm 3077
The LCN Door Closer Regular Arm 3077 ships with 95 percent of there door closers. This is the standard regular. Specify your current closers model number when ordering. Not all of the LCN closers have the same shape spindle on the door closer cylinder. The fitting for the 4040 is a six sided, the 4010, 4020 and 4110 have a flat sided oval, and the 1260 and 1460 have an eight sided star. The LCN Part #'s on this Regular Arm is: 1260-3077, 1460-3077, 4010-3077, 4020-3077, and 4040-3077. If your model is not here, call us and we will quote you a price.
3077 -
International Door Closer 854P Series
The International Door Closer 854P Series is a common closer we see on a lot of storefront aluminum framed doors. This is one of the last closers out there to still have sizing. By sizing I mean each door closer has a spring size of different tension so the closer is selected depending on door size and whether it is interior or exterior. These days we usually use this door closer as a replacement of existing doors. The closer features two adjustment valves for closing and latching speeds. The cylinder is constructed of precision cast aluminum. If you have an exterior door I would recommend the 880 Series, which is the same door closer, but has a back check valve. The back check valves will slow the door down if it is caught by a gust of wind. It ships with a regular arm and parallel arm bracket. This door closer is for use on doors up to 42” interior or 36” exterior doors.
3/4" x 9-1/16" mounting holes
854- -
International Door Closer 855P Series
The 855 has been discontinued. If you order it the 885 will be sent, it is the same door closer, but features back check.
The International Door Closer 855P Series is a common closer we see on a lot of storefront aluminum framed doors. This is one of the last closers out there to still have sizing. By sizing I mean each door closer has a spring size of different tension so the closer is selected depending on door size and wether it is interior or exterior. These days we usually use this door closer as a replacement of existing doors. The closer features two adjustment valves for closing and latching speeds. The cylinder is constructed of precision cast aluminum. If you have an exterior door I would recommend the 880 Series, which is the same door closer, but has a back check valve. The back check valves will slow the door down if it is caught by a gust of wind. It ships with a regular arm and parallel arm bracket. This door closer is for use on doors up to 48” interior or 42” exterior doors.
3/4" x 9-1/16" mounting holes
855- -
LCN Door Closer 4031
The LCN Door Closer 4031 is shipped with forged regular arm, metal cover and wood/self-tapping machine screw pack. Non-sized (1-4) 4031 cylinder for exterior doors to 36” (914 mm) and interior doors to 48” (1219 mm). Closer mounts hinge side, top jamb, and parallel arm, on either right or left swinging doors. Closer meets ADA requirements. The hole spacing on this closer will not match the 4030's that LCN produced up to 1997, that was a completely different door closer.
We ship the 4031 Rw/PA
4030- -
International Door Closer 885P Series
The International Door Closer 885P Series is a common closer we see on a lot of storefront aluminum framed doors. This is one of the last closers out there to still have sizing. By sizing I mean each door closer has a spring size of different tension so the closer is selected depending on door size and wether it is interior or exterior. These days we usually use this door closer as a replacement of existing doors. The closer features three adjustment valves for closing,latching speeds and one for back check. The cylinder is constructed of precision cast aluminum. It ships with a regular arm and parallel arm bracket. This door closer is for use on doors up to 48” interior or 42” exterior doors.3/4" x 9-1/16" mounting holes
885- -
LCN Door Closer Cover
The LCN Door Closer Cover is the standard plastic cover that ships with LCN Door Closers. Specify your current closers model number when ordering. Not all of the LCN closers have the same shape cover on the door closer cylinder. The part number is the Series Number followed by -72. So, the part number would be 1460-72, 4010-72, 4020-742, 4030-72, 4040-72 and 4110-72. We have access to all the covers, if yours is not here call us and we will quote you a price.
4XXX-72 -
International Door Closer 853P Series
The International Door Closer 853P Series is a common closer we see on a lot of storefront aluminum framed doors. This is one of the last closers out there to still have sizing. By sizing I mean each door closer has a spring size of different tension so the closer is selected depending on door size and whether it is interior or exterior. These days we usually use this door closer as a replacement of existing doors. The closer features two adjustment valves for closing and latching speeds. The cylinder is constructed of precision cast aluminum. If you have an exterior door I would recommend the 880 Series, which is the same door closer, but has a back check valve. The back check valves will slow the door down if it is caught by a gust of wind. It ships with a regular arm and parallel arm bracket. This door closer is for use on doors up to 32” interior or 28” exterior doors.
Direct replacement for the older style Norton 1602 and 1603, and Yale 52 and 53, that had the 3/4" x 8-3/16" mounting holes
853-