Parts| Sargent

When you purchase panic and exit devices from RBA Door, every product will meet local building codes as well as your expectations for performance and quality. All panic device hardware and accessories are built with durability, convenience and value in mind. No matter the project, our panic devices are a well-built choice at a reasonable price.

Filter
View as Grid List

Items 1-36 of 42

per page
Set Descending Direction
Page
  1. Sargent 646 Surface Strike

    The Sargent 646 Surface Strike is used on the 20, 30 and 80 Series Surface Vertical Rod Panic Hardware and Fire Rated Hardware.  It is used as a strike for the top latch. The strike measures 1-5/32" x 3-11/16"  with a 3/4" projection.   Strike features a black coated epoxy finish.

    Sargent Part #646

    G646
    $96.02
  2. Sargent 649 Surface Strike

    The Sargent 649 Surface Strike is used on the 20, 30, 60 and 90 Series Rim Panic Hardware.  The Strike measures 1-5/32" x 3-11/16"  with a 3/4" projection.   Strike features a black coated epoxy finish.

    Sargent Part #649

    649
    $96.02
  3. Sargent 624 Bottom Surface Strike

    The Sargent 624 Bottom Surface Strike is used on the 20, 30, 60, 80 and 90 Series Surface Vertical Rod Panic Hardware.  The Strike is mounted on the floor and the bottom latch locks on to it.   Strike measures 9/16" x 2-1/2" with a 3/8" projection.   Strike features a black coated epoxy.

    Sargent Part #624

    G624
    $69.58
  4. Sargent 655 Bottom Surface Strike

    The Sargent 655 Bottom Surface Strike is for use the 20, 30, 80 and 90 Series Surface Vertical Rod Panic Hardware.  The Strike measures 1-13/16" x 2-3/4" x 3/32" thick. 

    Sargent Part #655

    G655
    $40.36
  5. Sargent Lever Return Spring 97-0425

    The Sargent Lever Return Spring 97-0425 is usually a green color, however we have seen them in blue and red.  The red spring has the same dimensions as the green, but the loop on the coil side of the spring was closed.  Sargent is using this spring as a replacement for all of those springs.  If you have a Sargent Panic Hardware, and the lever is sagging, or just hanging, this is most likely the problem.  The spring measures 2-1/8" long  by roughly 3/8" diameter.

    Sargent part # 97-0425

    G970425
  6. Sargent 700 ET Spindle Kit 730-7

    Sargent 700 ET Spindle Kit 730-7

    This Sargent Kit 730-7 includes the spring, spindle and the associated plates. Look under "More Views" for a detailed look of this repair kit. The 730-7 is for 1-3/4" doors.   Shank measures 4-1/4" long, square spindle is 5/16" square.

    Sargent Part # 730-7

    G7307
    $58.44
  7. Sargent 97-0050 Knob Return Spring

    Sargent 97-0050 Knob Return Spring

    This Sargent Knob Return Spring measures 1-1/16" overall length by 3/16" diameter

    Sargent Part # 97-0050

    G970050
    $4.18
  8. Sargent 97-2434 Old Style 8700 Top Latch

    Sargent 97-2434 Old Style 8700 Top Latch

    The Sargent 97-2434 Old Style Top Latch was used on the 8706, 8710, 8713, 8715, 8728, 8740, 8743, 8746,  8762, 8763, 8773, and 8774 Series Surface Vertical Rod Devices before November 11, 2002.  We sometimes fine the casting number of 97-0317 stamped on the back of this latch.  This Top Chassis has 3 mounting holes.

    Sargent Part # 97-2434

    G972434
    $416.06
  9. Sargent 20/60 Plastic End Cap Only 68-0434

    The Sargent 20/60 Plastic End Cap Only 68-0434 will also work on the 30 Series Panic Hardware.   The cap has been manufactured for the last 40 years and is made of high impact plastic.  The end cap measures 1-5/8" wide by 2-3/8" tall and projects out 2-3/4".

    Sargent Part # 68-0434

    G20300C
    $31.48
  10. Sargent Exit Device 20/30/60 End Cap And Bracket

    The Sargent Exit Device 20/30/60 End Cap And Bracket is a part we put together here for your convenience.  Sargent only sells these components separately.  Usually only the cap goes missing, but every once and while the bracket goes missing also.  The package is used on the all of the 20, 30 and obsolete 60 series devices.

    Sargent Part # 68-0434, 68-2141, and 97-0052

    G20300
    $72.58
  11. Sargent 20/30/60 End Cap Bracket

    The Sargent 20/30/60  End Cap Bracket is used with the larger end cap.  This end cap has been manufactured for the last 40 years and started its life on the obsolete 60 Series.  The bracket holds the hinge side of the exit device on the door, and the G20300C fits over the top of it.

    Sargent part #68-2141

    G20300B
    $43.35
  12. Sargent 20/30/60/80 Connecting Arm Spring

    The Sargent 20/30/60/80 Connecting Arm Spring is the spring that pushes the touch pad back out after you push it in.   It is used on the 20, 30, 60 and 80 Series Panic Hardware.

    Sargent part # 68-0236

    G20200
    $8.35
  13. Sargent Panic Device Latch Bolt Spring

    Sargent Latch Bolt Spring.

    Used to put tension on the latch bolt of the 20, 30, 60, and 80 Series Sargent exit devices

    Sargent Part # 98-0028

    G20400
    $4.18
  14. Sargent 20/30/60/80 Dogging Kit 68-2596

    The Sargent 20/30/60/80 Dogging Kit 68-2596 is used on the Sargent 20, Sargent 30, Sargent 60, and Sargent 80 Series Panic Hardware. This dogging assembly kit has been around since the 1980's.  We only sell the dogging assembly parts as a complete set.

    Sargent part # 68-2596

    G80200
  15. Sargent 80 Series Plastic End Cap Only

    Sargent Exit Device 80 Series Plastic End Cap

    This part is the weak link in this exit device. When the end cap falls off the Dogging Cover Plate falls out also! The end cap is 1-1/8" wide by 2-7/16" tall and projects out 1-7/8".

    Sargent Part # 68-0561

    G80300C
    $27.14
  16. Sargent 80 Series Metal End Cap And Bracket 565

    Sargent Exit Device 80 Series Metal End Cap And Bracket

    Use this end cap to replace all older versions and plastic end caps. It is much stronger then the orginals, more impact resistant.

    sargent part # 565

    G80300SS-
    As low as $68.19
  17. Sargent Exit Device 80 Series Plastic End Cap And Bracket

    Sargent Exit Device 80 Series Plastic End Cap And Bracket

    includes the end cap, bracket and mounting screws. This plastic end cap always breaks. You might want to consider trying the new impact resistant end cap shown in the related products, on the right hand margin of the page.

    Used on the Sargent 80 Series Exit Devices

    Part #'s 68-0561, 68-0511 and 97-0052

    G80300
    $65.41
  18. Sargent 80 Series End Cap Bracket

    Sargent Exit Device 80 Series Bracket

    Used on to hold exit device on door, plastic end cap mounts to it.

    Sargent part # 68-0511

    G80300B
    $41.75
  19. Sargent 97-3230 Cylinder Dogging Assembly

    Sargent 97-3230 Cylinder Dogging Assembly

    The Sargent 816 Cylinder Dogging Assembly, also known as the 97-3230, includes the cam that the cylinder dogging tends to wear out.

    Sargent Part # 97-3230

    G973230
    $44.53
  20. Sargent 60/80 Push Bar Pins 68-0230

    Sargent 60/80 Push Bar Pins-Long Pin

    Also known as the channel axle or pin. This is the pin you see on the exit device channel, the wider of the two pins.

    2-3/16" LONG

    Sargent part # 68-0230

    G680230
    $33.40
  21. Sargent 60/80 Push Bar Pins 68-0229

    Sargent 60/80 Push Bar Pins-Short Pin

    Also known as the push bar axle, this is the pin that you see on the push pad.

    1-9/16" LONG

    Sargent part # 68-0229

    G680229
    $33.40
  22. Sargent 60/80 Push Bar Pin Retaining Clip

    Sargent 60/80 Push Bar Pin Retaining Clip

    used on Sargent 60 and 80 series to retain the push bar and channel axles. Use with the 68-0229 and 68-0230.

    Sargent part # 01-0098

    G010098
    $1.40
  23. Sargent Panic Device 68-4261 8800 Chassis Assembly

    Sargent Exit Device 8800 Chassis Assembly

    Chassis for devices after 2/5/2001. Used on the 8804, 8806, 8810, 8813, 8815, 8840, 8843, 8844, 8846, and 8888 Sargent Exit Hardware Devices.

    Sargent Part # 68-4261

    G684261
    $555.21
  24. Sargent 80 Series Lexan Touch Bar Kit 809

    Sargent 80 Series Lexan Touch Pad Kit

    Sargent 80 series Lexan Touch Pad Kit replaces old and or broken touch pad inserts. On the Sargent part break downs this would be Touch Bar part number 68-0607 and Base 68-0606. The base is 13-1/2" long with 3 mounting holes 4" apart on center.

    Sargent Part # 809 KIT

    G80500
    $50.09
  25. Sargent 97-0300 8700 Top Latch Spring

    Sargent 97-0300 8700 Top Latch Spring

    The Sargent 97-0300 8700 Top Latch Spring is used on most of the new and older style Sargent Panic Devices.   The springs measures 1-5/8" overall length.

    Sargent Part # 97-0300

    G970300
    $19.48
  26. Sargent 28-0109 Center Case Cam for 2828 / 2838

    The Sargent 28-0109 Center Case Cam for 2828 / 2838 is the Cam that the key cylinder actuates to open the door.   The cam is located in the middle of the Center Case.  This piece ships with the 01-9167 Retaining Ring.

    Sargent Part # 28-0109

    G280109
    $4.87
  27. Sargent 90 Lever Arm Spring 97-0012

    Sargent 90 Lever Arm Spring

    Used on the 9800 series Sargent Exit Devices. 1-3/4" LONG by 9/16" DIAMETER

    Sargent Part # 97-0012

    G90400
    $4.87
  28. Sargent 90 Series Mouse Trap Spring 98-2159

    Sargent Exit Device 90 Series Mouse Trap Spring

    Used on the Sargent 9898 Rim Device on the opposite side of the case as the latch bolt.  The plate measure 1-3/16" by 1-1/2"

    Sargent part # 98-2159

    G90500
    $36.18
  29. Sargent Panic 97-0008 End Plug

    Sargent Panic 97-0008 End Plug

    Sargent 97-0008 End Plug and 01-001 End Plug Screw.  Fits the 90 series cross bar panic devices.

    G90300-
    As low as $19.48
  30. Sargent 2828 Series Rim Panic Device

    Simplicity
    • Engineered with minimum components and maintenance-free
    • Modular design allows for phased component installation. Chassis assembly can be mounted separately to secure the door during construction
    • Retrofits to all applications
    • One chassis design to accept all available functions/trims
    Durability
    • Reinforced cast (ZA) alloy chassis – exceptional strength and durability. Withstands 2X more static load forces compared to a stamped steel chassis
    • Endures over 4 times the ANSI/BHMA A156.3 2001 Grade 1 cycle testing standard
    • Non-handed rim; reversible vertical rod
    • Solid stainless steel latch. Meets UL panic test requirements without roller strikes which compromise strength and durability
    • Three year warranty

    G20EO-
    As low as $670.70
  31. Sargent 2727 Panic Device

    Simplicity
    • Engineered with minimum components and maintenance-free
    • Modular design allows for phased component installation. Chassis assembly can be mounted separately to secure the door during construction
    • Retrofits to all applications
    • One chassis design to accept all available functions/trims
    Durability
    • Reinforced cast (ZA) alloy chassis – exceptional strength and durability. Withstands 2X more static load forces compared to a stamped steel chassis
    • Endures over 4 times the ANSI/BHMA A156.3 2001 Grade 1 cycle testing standard
    • Non-handed rim; reversible vertical rod
    • Solid stainless steel latch. Meets UL panic test requirements without roller strikes which compromise strength and durability
    • Three year warranty

    exit device handing diagram

    2727EO-
    As low as $1,193.91
  32. Sargent 20 Series Dummy Trim

    • For 1-3/4" (44mm) doors standard
    • Through-bolted with 3 mortise nuts
    • Pulls project 1-1/2" (38mm) from door face
    • GTB Design trim will cover a 161 cutout

    28-D-GTB-
    As low as $64.70
View as Grid List

Items 1-36 of 42

per page
Set Descending Direction
Page