Search results for: 'Replacement parts for Secrity Latch Single Door'
-
Anodized Black Aluminum Door Kick Plate 315AN
The Anodized Black Aluminum Door Kick Plate 315AN are a flat black and match the black color we find on Storefront doors. These plates have an aluminum base metal, which is 18 gauge (.040") thick that is then Anodized in the Black Color. These plates relatively inexpensive. Custom sizes are available, they run about $0.25 per square inch.
You can order these plates with tape mounting, but on larger plates and especially plates with a stainless steel base metal, it is not recommended. Stainless Steel plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes. This is fine on the Brass and Aluminum base metals, but again Stainless Steel is very hard and a drill press would be recommended. You can glue them on, I would recommend liquid nails, and come C Clamps with the door on saw horses.
GKP-BLK -
Von Duprin 22 Mechanism End Cap 900981
The Von Duprin 22 Mechanism End Cap 900981 is the end cap and bracket that ships with the 22 and 2227 series. The bracket is constructed of zinc plated steel and the end cap is black plastic. Bracket also acts as mounting bracket that holds the exit device on the door. Von Duprin does offer a new Metal End Cap, look under related products.
Von Duprin part # 900981
G22R10 -
Cal-Royal 45 Narrow Stile Surface Vertical Rod
The Cal-Royal 45 Narrow Stile Surface Vertical Rod is part of the new 4500 Series. They are designed for Narrow Stile Doors with a Stile width of at least 1-3/4 inches. The device is rated as a Grade 1, which is the heaviest traffic rating possible. They ship with all mounting hardware and strikes. This device is non handed and uses a Allen Type dogging system.
45-SVR -
Cal-Royal 45 Narrow Stile Rim Device
The Cal-Royal 45 Narrow Stile Rim Device is part of the new 4500 Series. They are designed for Narrow Stile doors with a minimum of an 1-3/4" stile width. This is a Grade 1 Exit Device, which is the highest traffic rating possible. Exit device ships with strike and mounting screws.
Shown is Left Hand Reverse
Opposite would be Right Hand Reverse45-RIM -
Von Duprin 99 Cover Plate 050114
The Von Duprin 99 Cover Plate 050114 is for use on the 33A, 35A, 98 and 99 devices. Covers the dogging assembly on the hinge side of the door. The usually fall off when the End Cap is not on the exit device. Von Duprin is only shipping a 20-1/2" cover plate now, which will work on 3' and 4' doors, you will have to cut more off if you have a 3' device with a hack saw or chop saw.
Von Duprin Part # 050114 and 050117 Hex Key Dog Conversion Kit
Von Duprin 99 Cover Plate 050114
G99R50 -
Clear Plastic Door Kick Plates
The Clear Plastic Door Kick Plates are constructed of .125" thick acrylic. We recommend screw mounting on these plate, because you can see right through them, and would be able to see the Tape Mount or Glue. We have the more common sizes listed, but If you need a custom size they run about $0.22 per square inch.
GKP-CP -
Door Push Plate 59
The Door Push Plate 59 has the classic half round design. The plate measure 7-1/2" wide and 15" tall, and is constructed of 16 gauge metal, which is .050" thick. This plate is similar to the GPH60 (Push Plate 59), but is a 1/2" more narrow and 1" shorter. This plate ships with the matching finish screws.
Aluminum and Stainless Steel ship in 1 week, all other finishes ship in 2 weeks. Made in the USA.
GPH59- -
LCN 4410HSA Sentronic
The 4412HSA SENTRONIC® is an electrically controlled closer/holder designed to provide easy passage for groups of pedestrians through high traffic doors. Pedestrians, moving through the doorway, trigger the built-in scanner. When the door is opened to 80° or more, the door is electrically held open to minimize wear and tear on applied door hardware. After the last pedestrian in a group passes through the doorway, the system timer releases the hold-open, closing the door under control of the heavy duty closer. Double lever arm closer is specifically designed for push side mounting. Choice of finishes and accessories meet virtually all high traffic installation requirements.
4410HSA -
Rixson 117 Hinge Set
Application
includes 180 top pivot
Interior Doors
Weight to 300 lbs.*
Door Width up to 3'6"(1067mm)
Handed117 -
Von Duprin Panic Device 880NL Trim
The Von Duprin Panic Device 880NL Trim is for the 88 Series only. The stanchions welded on the back of the plate line up with the88 device on the interior. Optional key cylinder locks and unlocks the device, and can be used for dogging the door open. Plate measures 3" wide by 14-3/16" long, with an 1-5/8" bore for cylinder.
Von Duprin part # 880NL-R
880NL -
Door Push Plate 58
The Door Push Plate 58 is the only plate we have that is a forged plate. The forging process involves heat and pressure or pounding. The result is a very heavy and durable metal. This plate measures 3-1/2" wide by 15" tall, with a thickness of 7/32". This is one of the thickest plate we offer, and is the most sturdy.
GPH58- -
International Door Closer 8610S Rim Device-Grade 1
International 8610S Rim Device-Grade 1
DC 8000 Series Exit Devices are heavy duty and designed for heavy traffic applications. The devices are Underwriters Laboratory (UL, USA and ULC, Canada) listed for Panic Exit Hardware or Fire Exit Hardware, and are certified to ANSI A156.3-2001 Grade 1.
Non handed, 4-1/2" minimum stile width. Smooth Surface.
8610S- -
Corner Guard 301 1" X 1.75"
The Corner Guard 301 are a great way to protect corners and edges of doors. Fabricated from 16 gauge (.050") thick metal they measure 1" on one arm and 1-3/4" on the other, and can come in any length. Standard lengths are 36", 42" and 48", but we have the capability to modify to your specifications. This product is ideal for high traffic or areas of high abuse. They come standard with screw mounting, but other options are available.
Screws included for mounting
GCG301 -
Sargent 700 ET Retrofit Kit 730-1
Sargent 700 ET Spindle Kit 730-7
This Sargent Kit 730-7 includes the spring, spindle and the associated plates. Look under "More Views" for a detailed look of this repair kit. The 730-7 is for 1-3/4" doors. Shank measures 4-1/4" long, square spindle is 5/16" square.
Sargent Part # 730-7
G7301 -
Wall Door Stop / Bumper Heavy Duty Convex WS402CVX
The Ives WS402CVX Wall Door Stop is our heaviest duty wall stop of this design. They are constructed of a heavy duty cast brass base that is then plated to your desired finish. The wall stop is 2-1/2" in diameter and has a 1" projection. It features a special retainer cup that makes the rubber tamper resistant. This stop ships with screw and drywall anchor.
GJ50C- -
Falcon 25-V Vertical Rod Panic Device
Falcon 25-V Vertical Rod Panic Device
The Monarch Falcon 25-V is designed for high-traffic applications were added strength and durability are required. The device includes all strikes and mounting screws required for installation. Available in 3' and 4' devices, the 3' device is for doors 30" to 36", the 4' device is for doors that are 37" up to 48" wide. The vertical rods furnished with this device are for doors up to 7' tall, if your doors are taller, please contact us.
G25VEO- -
Wall Door Stop / Bumper Heavy Duty Concave WS401CCV
The Ives WS401CCV Wall Door Stop is our heaviest duty wall stop of this design. They are constructed of a heavy duty cast brass base that is then plated to your desired finish. The wall stop is 2-1/2" in diameter and has a 1" projection. It features a special retainer cup that makes the rubber tamper resistant. This stop ships with screw and drywall anchor.
GJ60C- -
Oil Rubbed Bronze Door Kick Plate
Our Dark Bronze Oil Rubbed Bronze Door Kick Plates (US10B) are a baked on powder coat on brass base metal. We switched to this finish 5 years ago due to color variations in the US10B Oil Rubbed Bronze finishes. The US version was much lighter than the Asian version, which is where most the door hardware is made these days. The cost of Oil Rubbing was going through the roof and many platers were having issue with the environmental impact and EPA regulations in the United States. Our Oil Rubbed Kick Plates are 16 gauge (.050″) thick.
Kick Plates can be mounted by screws, two way tape, and they can be glued to the door. Our plates come standard with screw mounting. The manufacture sends #6 x 5/8″ Oval Phillips Undercut dark brown screw. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10″ will have 10 holes for plates up to 33″ and 12 holes for plates between 33 and 40″.
You can order these plates with tape mounting, but on larger plates, it is not recommended. Large plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes. You can glue them on, I would recommend liquid nails, and some C Clamps with the door on saw horses.
Custom sizes available starting around $0.49 per square inch depending quantity
Please allow 2 week shipping time
GKP-DB -
Door Push Plate 61
The Door Push Plate 61 is constructed of 16 gauge stainless steel, aluminum, brass or bronze. This plate is handed left and right, the one shown on the website is a Left Hand plate. They measure 7-1/2" wide by 15" long, and ships with the matching finish mounting screws.
GPH61 -
Lifetime Brushed Brass Door Kick Plate
The Lifetime Brushed Brass Door Kick Plates are the same as the Lifetime Polished Brass Door Kick Plates, solid stainless steel base metal, 16 gauge (.050" thick), but the surface is Satin or Brushed. Because it is an artifical finish they will not tarnish. Custom sizes available starting around $0.41 per square inch depending quantity. Kick Plate comes with screws for mounting. Please allow 1 week shipping time.
GKP-BB -
LCN 1370 Quick Fix Plate
The LCN 1370 was a door closer made in the late 1990's to 2006 or so. The closer had a special mounting plate that made installation very quick. Many people have this door closer in use and now they are starting to fail. The LCN 1370-18QF Quick Fix Plate converts the mounting holes of the 1370 to a standard template closer, which is 3/4" x 9-1/16". By using this plate you will not have to redrill holes in your door. The plate measures 2 by 10-1/4 inches with tapped holes that measure 3/4 x 9-1/16 inch.
1260-18QF- -
Door Pull Plate 5020
The Door Pull Plate 5020B is constructed of .050" wrought metal, in either solid aluminum, brass or stainless steel, with Door Pull GHE20 -8" center. Handles come with thru bolts, finish washers and the plates come with sheet metal screws that fit the countersunk holes.
GPL20B -
International 8730S Narrow Design Surface Vertical Rod
The International Door Closer 8730S is designed for narrow stiles. The minimum stile width is 2-19/32 inches. It will not work on a true narrow stile door witch is usually 1-3/4 inch. The 36 inch version is 33-15/32 inches and the 48 inch version is 44-3/4 inches. The device is rated Grade 1, which is the highest rating. Rods are 1/2 inch diameter tubular with rod guides. The exit ships will all screws and strikes need for instillation.
8730S- -
Door Pull Plate 5010
The Door Pull Plate 5010 is .050" wought solid aluminum, stainless steel, or brass depending on the finish. The Door Pull GHE10, handles come with thru bolts. The plate has counter sunk holes and sheet metal screws in matching finish.
3" x 12" GPL312
3.5" x 15" GPL315
4" x 16" GPL416GPL10 -
Duranodic Aluminum (Dark Brown) Door Kick Plate
The Duranodic Aluminum (Dark Brown) Door Kick Plates are dark bronze or brown and match the Dark Brown color we find on Storefront doors. These plates have an aluminum base metal, which is 18 gauge (.040") thick that is then Anodized in the Dark Brown Color. These plates relatively inexpensive. Custom sizes are available, they run about $0.25 per square inch.
You can order these plates with tape mounting, but on larger plates and especially plates with a stainless steel base metal, it is not recommended. Stainless Steel plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes. This is fine on the Brass and Aluminum base metals, but again Stainless Steel is very hard and a drill press would be recommended. You can glue them on, I would recommend liquid nails, and come C Clamps with the door on saw horses.
GKP-xxxDB -
Lifetime Polished Brass Door Kick Plate
The Lifetime Polished Brass Door Kick Plate has a 16 gauge (.050″ thick) base metal, that is then plated with a artificial brass finish that is then polished. The process is called Poly Vapor Deposition or PVD, which is why we hear the name Lifetime Polished Brass Kick Plate PVD. Because the finish is an artificial brass, it does not have to be clear coated, so it will never tarnish. The Lifetime Polished Brass finish cost the same as the Solid Brass Polished Kick Plates.
Our plates come standard with screw mounting. The manufacture sends #6 x 5/8″ Oval Phillips Undercut brass screws. The number of holes on the screw mounted plates is determined by an industry wide standardize template. A height between 6-10″ will have 10 holes for plates up to 33″ and 12 holes for plates between 33 and 40″. You can order these plates with tape mounting, but on larger plates, it is not recommended, the plates are too heavy and they most likely will not stick. We can also ship them with no holes, if you want to drill your own holes, but they are made of Stainless Steel, which is a tough metal to drill. You can glue them on, I would recommend liquid nails, and come C Clamps with the door on saw horses.
Custom sizes available starting around $0.40 per square inch depending quantityPlease allow 1 week shipping time
GKP-US3-PVD