Search results for: 'dorma slidind door case dor mani von'
-
Von Duprin Panic Device 880TP Trim
The Von Duprin Panic Device 880TP Trim is for the 88 series only. The stanchions welded on the back line up with the 88 device on the interior. The optional key cylinder locks and unlocks the thumb piece. The plate measures 3" wide by 14-3/16" long with an 1-5/8" bore hole for cylinder.
Von Duprin part # 880TP-R
88TP- -
Dor-o-Matic 1590 159CA-NL Cylinder Assembly
No longer available
Doromatic 1590 Cylinder Assembly 159CA-NL
Doromatic part # 159CA-NL
159CA-NL -
Von Duprin 2227 Rod Guides Assembly 112063
The Von Duprin 2227 Rod Guides Assembly 112063 works on all of the Von Duprin 2227's, and replaces the older style that featured the plastic cap and the springs. This device is used to add strength and rigidity to the top and bottom rods on there surface vertical rod.
Von Duprin part # 112063
G22VR80- -
Wall Door Stop / Holder WS40
The Ives Wall Door Stop / Holder WS40 is a door holder that has some history. We see this product in many schools, hospitals and churches that were built in the 50's, 60's and 70's. The WS40 was originally made and designed by Glynn-Johnson out of Chicago, Illinois, and was called the W40 or GJW40. H.B. Ives purchased Glynn-Johnson in 1990's and mergered this product into there offering, and changed the part # to WS40. The holder is made of cast brass or bronze and plated to your desired finish. The holding mechanism has a rubber bumper inside it to act as a door stop, and a brass spring loaded roller to act as a holder. The product ships with a universal screw package to mount on all types of walls. For the best results with this stop/holder the door and wall should be about 3-1/2" apart in the open position.
Base Height: 2"
Base Width: 2-1/2"
Base Projection: 2-1/4"
Engaged Projection: 3-1/2"
Strike Height: 2-1/16"
Strike Width: 3/4"
Strike Projection: 2"GJW40- -
2390 Falcon Dor-o-matic Anchor Block Assembly
The Doromatic 2390 Anchor Block Assembly is used to connect the push bar to the device channel.
Discontinued December 2024
G2390ABS -
Von Duprin 050611 Lever Trim Shear Pin | Von Duprin Panic Hardware
Von Duprin Exit Device Lever Trim Shear Pin Kit
This is the component that is designed to break, if the lever handle is forced to open , this pin snaps so your trim is not destroyed. 3/16" diameter shaft by 5/8" overall length. Retaining Ring included. This shear pin is used on the 230L, 360L, 992L, 994L and 996L Von Duprin Lever Trims.
Von Duprin Part # 050611 Old Part # 971583
G050611 -
International Door Closer 5001P Series Adjustable Spring Power
The International Door Closer 5001P Series Adjustable Spring Power is a great closer to use as a replacement for the many 3/4" by 12" mounting holed closers. This door closer is fully adjustable with sweep, latching and back check adjustments, a long with an adjustable spring tensoin control. This closer can be adjusted to less then 8-1/2" pounds of resistance to meet ADA standards. You can install this closer on the push, pull or top jamb, we ship the regular arm and a parallel arm bracket. This closer has the same mounting holes as the Norton 8000 and Yale 3000 door closers.
Hole spacing 3/4" x 12"
5001- -
Floor Door Stop / Holder FS42
Floor Door Stop / Holder FS42
This floor mounted door holder has been around since the 1960's. It used to go by the name Glynn Johnson GJF42A or F42A, and was brought over to the H.B. Ives line in the 1990's and now goes by the part # FS42. Many schools and hospitals have this door holder in use today. It features: Automatic door holders ideal for heavy-traffic situations that require a simple, fool-proof, Hold-Open device. Forged from brass. Unit is activated automatically when door is opened. A firm pull on door releases the mechanism. Strikes accommodate different door to floor clearances. Model numbers are determined by strike/door-to-floor clearances. Holder position on door is adjustable.
Door to Floor Clearance 1-1/8" to 1-9/16"
Holder Dimensions 3" Wide x 3-11/16" HighGJF42A- -
Von Duprin QEL Baseplate Conversion Kit
The Von Duprin QEL Baseplate Conversion Kit is for use on the 33A, 35A, 98, and 99 exit devices. The size is the size of the exit device. The 98/99 device 36" would be 33" wide device and the 48" would be for the 45" device. The 33A/35A the 36" would be for the 35-3/8" wide device and the 48" would be for the 47-3/8" wide device.
Von Duprin Part # 958003 3' Device
Von Durpin Part # 040065 4' DeviceG95800x -
Von Duprin 22 Control Link Pin 050529
Von Duprin 22 Control Link Pin
The control link pin is the connector pin, that connects the latch head assembly to the push bar assembly. When the push bar is pushed in it retracts the latch bolt and the pin connects the two pieces. This Control Link Pin is used on the Von Duprin 22, 33A, 98 and 99 Panic Devices.
VON DUPRIN PART # 050529
Old Von Duprin Part # 969520G22R60 -
Von Duprin 110388-00 6 Foot EL Cable Assembly
The Von Duprin 110388-00 6 Foot EL Cable Assembly connects directly into your power source and the Potted Circuit Breaker 050534. This 6 foot Cable Assembly is used on Von Duprin and Falcon Exit Devices that have the Electric Latch Retraction.
Von Duprin Part # 110388-00
G110388 -
Von Duprin Strike 264
The Von Duprin Strike 264 measures 2-7/8" tall by 1-1/4" wide with a roller projection of 9/16". Used on the Von Duprin 22, 88, 98 and 99 when a lower profile strike is need in place of the Von Duprin 299 Strike. The hole spacing is 2-1/8" on center, and it ships with mounting screws and a shim. Also known as a Von Duprin Surface Roller Strike.
Von Duprin Part # 264
264 -
Von Duprin EL99 Panic Device Only
This is the same trusted Von Duprin 99 with Electric Latch Retraction, also known as EL.
The EL feature allows for the remote unlatching of exit devices. A control station operator can flip a switch to retract the latch bolt and immediately change an exit door to push-pull operation. A powerful, continuous duty solenoid retracts the latch bolt, either for momentary unlatching, or for extended periods of time. The EL feature is an alternative to manual dogging.
EL devices are also useful with automatic door operators, and may be applied to fire-rated applications when under the control of an automatic fire alarm system.
UL approved for Class II circuit applications.
The EL option does not include the power transfer from door to frame, the power supply, or the control operator. Refer to EPT-2 power transfer and the PS914 power supply.
The PS914 with the 9002RS option card is the minimum option card required. Other option cards available for other functions, see PS914 power supply for additional information.
Ships with all the mounting screws and the 299 Strike.
EL99EO-Von Duprin 9927 Bottom Vertical Rod 110574
The Von Duprin 9927 Bottom Vertical Rod 110574 is the replacement rod for broken or bent vertical rods. All of the 9927 bottom rods are the same length, this is set by Federal Building Codes, so the center line of the Panic Hardware is a certain height from the finished floor. The length of the rod is 31-1/4" long, less the fittings. The old part number on this was 110574, and the newer one is 050514.
G99VR50-Von Duprin 100316 5547 Top Plate
The Von Duprin 100316 is used on the 5547 on the top of the door. The top rod goes through the square hole on the plate. The plate shown in the Picture has both sides or LHR and RHR doors. One side of the strike is usually broken off depending on the hand of the door.
G100316Von Duprin 050500 88 Latch Tail Kit
Von Duprin 050500 88 Latch Tail Kit
The Von Duprin Part # 050500 includes the 1 Latch Tail, 2 Latch Tail Rivets, and 2 Latch Tail Springs. This product is used on the Von Duprin 88 Rim Device, for the EO, NL, TP and DT functions. This is not the Latch Tail Kit used on the Fire Rated Von Duprin 88-F Devices.
Von Duprin Part # 050500
G050500Von Duprin 88 Lever Arm Right Hand 050438
The Von Duprin 88 Lever Arm Right Hand 050438 replacement lever arm for all the Von Duprin 88 exit devices. Usually replaced due to the dogging screw stripping out. The arm includes the Wedge, Wedge Ring, Wedge Tite Screw and Dog Screw, and sometimes the axle.
Von Dupin part # 050439
Old Part # 10072988R80-Von Duprin 55NL Cam
The Von Duprin 55NL Cam is one of the handed parts in the housing, the other is the Arm. If you need to change the hand of a housing, you just need to order the other hand Cam.
The Cam shown in the Picture is Right Hand
Von Duprin Part #'s 050355-Right Hand, 050356-Left Hand.
G050355-6Von Duprin Panic Device 99 Lever Trim
The Von Duprin Panic Device 996L Lever Trim has an escutcheon plate that measures 2-3/4" wide by 10-3/4" high and projects out 27/32". The handle projection is 2-7/8". The key cylinder, not included, locks and unlocks the lever. This lever handle is handed, but is field reversible. Key lock and unlocks lever. We ship the 996L-R&V
99LDor-O-Matic 2090 Panic Device
The Dor-O-Matic 2090 Panic Device has been around since the early 1970's. Even though it is now called the Falcon 2090 Panic Hardware, it is the same exact device. The 2090 provides balanced appearance, dependable performance and economical pricing, making it a popular choice where rim exit devices are required. The package includes both housings, 41" crossbar (that can be cut in the field), mounting screws and strike.
Hand: Specify RHR or LHR, not reversible. See Below
Left Hand Reverse shown in picture
Latchbolt: 1/2" throw hardened steel.
Dogging Feature: Hex dogging standard.
Sizes: Field adjustable width, 41" crossbar standard, fits
3' 8" door width, extra length crossbars available.
Doors: 1-3/4" thick metal or wood doors, specify if wood door.
Projections: 4-3/8" extended, 2-1/2" depressed.
Stile: 1-3/4" minimum.Replacement parts are also available
G2090EO
